top of page
OIL LEVEL INDICATING PRODUCTS
BRASS STANDARDIZED OIL GAUGES
Our oil gauges are made in standard sizes as indicated in table, but they can also be made in various combinations to meet special requirements. Specify Model and Size No. when ordering.
CAN BE FURNISHED UP TO 30” LONG
* Length applies to those gauges which have shanks, Models EFI 526 and 527. Height and Length are measured from center line of base to top of gauge and end of shank respectively.
MODEL EFI 527
MODEL EFI 524
MODEL EFI 522
MODEL EFI 526
BRASS OIL GAUGES
WITHOUT SHIELD
MODEL EFI 202
SHIELDED OIL GAUGE
WITH SHUT-OFF VALVE
CONSTRUCTION: BRASS
MALE PIPE THREAD -
Sizes 3/8”, 1/2”, and 3/4” NPT
Glass can be drained, cleaned or replaced by closing valve. It is not necessary to drain tank or reservoir.
TYPICAL APPLICATIONS: Used to indicate level of lubricating oil supply at bearings, gear boxes, crank cases, transformers, switches, etc. Designed to operate at atmospheric pressure and a maximum temperature of 225°F.
PROTECTED VENT: Vent hole allows free air communication with atmosphere minimizing possibility of dust or dirt getting inside gauge.
When ordering, Specify “A” Dimension
CAN BE FURNISHED UP TO 30” LONG
SNAP LEVER SIGHT
FEED OILER WITH SNAP FILLER OPENING
CONSTRUCTION: BRASS
To operate cup: Raise lever to stand perpendicular. Raise or lower the valve stem by turning the milled nut until the proper feed is obtained. To flush bearing move lever to an angle of 45°. Illustration shows cup with feed shut off.
MODEL EFI 33-A
MODEL EFI 5050A
HIGH-TYPE SHIELDED OIL GAUGES
CONSTRUCTION: STEEL/ZINC PLATED
GASKETS: BUNA-N
Pressure Rating: Atmospheric @ 225°F
APPLICATIONS: Used to indicate level of lubricating oil supply at bearings, gear boxes, crank cases, transformers, switches, etc.
PROTECTED VENT: Vent hole in cap nut allows free air communication with atmosphere – minimizes possibility of dust or dirt getting inside gauge.
Furnished with Redline Gauge Glass
MODEL EFI 4-8200
MODEL EFI 3-8200
FLUSH MOUNTING SHIELDED GAUGE
CONSTRUCTION: ALUMINUM, BRASS, STEEL, STAINLESS STEEL
For Operating Pressures up to 270 PSI
and Maximum Temperature 150°F
Size 1/2” NPT or 1/2-20 UNF Thread
Furnished with Redline Gauge Glass for easy indication of liquid level
Dimensions in Inches
Model
A
B
C
EFI 80-G-607
EFI 81-G-607
EFI 82-G-607
EFI 83-G-607
EFI 84-G-607
EFI 85-G-607
EFI 86-G-607
EFI 87-G-607
EFI 88-G-607
EFI 89-G-607
3
4
5
6
7
8
9
10
11
12
1-1/2"
2-1/2"
3-1/2"
4-1/2"
5-1/2"
6-1/2"
7-1/2"
8-1/2"
9-1/2"
10-1/2"
4-5/8"
5-5/8"
6-5/8"
7-5/8"
8-5/8"
9-5/8"
10-5/8"
11-5/8"
12-5/8"
13-5/8"
FLUSH MOUNTING SHIELDED GAUGES
CONSTRUCTION: STEEL/ZINC PLATED
Available with Thermometer (EFI 740) or without (EFI 5-8200)
Pressure Rating: 125 PSI @ 225°F
Size: 1/2-20 UNF Thread (furnished with 3/8” or 1/2” NPT adaptors, when specified)
Furnished with
Redline Gauge Glass
and Buna-N O-rings
MODEL EFI 740
MODEL EFI 5-8200
bottom of page